Skip to main content

ATmega8A (ATmega8) Development Kit

$24.50

10 in stock

QtyPrice
1 - 4$24.50
5 - 9$23.28
10 +$22.05
SKU: KT-MC-ATMEGA8A Categories: , Brand: .

Description

The ATmega8a development kit is based on our 28 pin development board which is compatible with many Atmel AVR microcontrollers. This kit is an easy and low cost way to get started with microcontrollers.

Included in the kit is the development board, an Atmega8a microcontroller, external crystal with supporting capacitors, AVCC filter parts, a 10 pin ISP connector, Power supply parts and more. For a full list, please refer to “What’s Included” below.

The Atmel Atmega8a microcontroller replaces the atmega8 which was discontinued in 2008. It is an 8-bit microcontroller with 8KB of flash, 1KB of RAM and 512 bytes of EEPROM. It has 23 I/O lines, 3 PWM channels and a 6 channel, 10-bit AD Converter. It sports dual 8-bit Timers each having separate prescalers and compare modes. Additionally it has a single 16-bit timer with a separate prescaler, compare and capture mode. I could go on but suffice to say, the Atmega8A is a feature packed and very versatile microcontroller.

The development board measures 127 x 94mm (5″ x 3.7″) and conforms to the Protostack large-size form factor. It has 6 mounting holes and can be stacked with other large, medium and small boards. It is made of quality 1.6mm FR4 substrate and uses 1oz per sqr foot copper. All holes are through plates and treated with lead-free HASL. The board includes areas for:

  • The 28-pin Microcontroller
  • AVCC filter
  • External crystal oscillator and supporting capacitors
  • Pullup resistor (10KΩ)
  • Reset switch
  • 10 pin ISP connector (standard ICSP 10-pin pinout)
  • 6 pin ISP connector (standard ICSP 6-pin pinout)
  • Dual row area for IDC connectors, USB connectors or other dual row components
  • Large prototyping area
  • VCC power bus, and
  • GND power bus.

The board supports many power supply configurations, including

  • L7805 regulator with barrel connector
  • L7805 regulator with polarised header
  • L7805 regulator with terminal block
  • LD1117 regulator with barrel connector
  • LD1117 regulator with polarised header
  • LD1117 regulator with terminal block
  • Stacking header bringing power from another board in a multiboard stack
  • Regulated power via barrel connector
  • Regulated power via polarised header
  • Regulated power via terminal block
  • CR2032 Batter clip solder on the board

All of these options are covered in the User’s Guide in section 4.6.

Being a through-hole kit it is suitable for beginners. Full assembly instructions are available from our User’s Guide.

Whilst many AVR programmers will work with this board, we recommend the USBASP AVR Programmer.

Included in each Kit

Part Number Description Quantity
PB-MC-AVR28 28 Pin AVR Development Board 1
CN-IC-2803 IC Socket 28 pin 7.62mm (0.3″) 1
IC-ATMEGA8A-PU ATMEGA8A-PU Atmel 8 Bit 8K AVR Microcontroller 1
PA-RY-MFQ1K Resistor – Metal Film 1/4W – 1K 1
LE-5M-YE LED General Purpose 5mm Yellow 1
CN-DC-21M DC Jack 2.1 x 5.5mm 1
SC-DI-1N4004 1N4004 General purpose 1A Rectifier Diode 1
SC-VR-L7805 L7805 +5V Linear Voltage Regulator 1
PA-PTC-500 PPTC Resettable Fuse – 72V, 500mA (RXEF050) 1
PA-CA-EL47U Capacitor – Electrolytic 25V 47 uF 1
PA-CA-EL100U Capacitor – Electrolytic 25V 100 uF 1
CN-ID-MR10 IDC Male connector (shrouded header), 10 pin, right angle leads 1
PA-RY-MFQ10K Resistor – Metal Film 1/4W – 10K 1
SW-TM-SPST Micro Tactile momentary SPST switch 1
PA-CY-16M 16MHz Crystal in HC/49S through hole package 1
PA-CA-CA22P 22pF 100V Resin Dipped Ceramic Axial Capacitor 2
PA-CA-CR100N Capacitor – Resin Dipped Ceramic 50V 100nF 3
PA-IN-AX10U Inductor (Choke) – 10μH, Axial leaded 1

Reviews

There are no reviews yet.

Be the first to review “ATmega8A (ATmega8) Development Kit”

Shopping Cart